Water and Gas Plumbing Hacks You Should Know

Indeed, few water and gas plumbing issues can be costly and time-consuming at times and they can take a toll on your sanity as well. By and large, people do not pay much attention to their water and gas plumbing needs until they start displaying the signs of damage.  So are you waiting for that?

Well, when it comes to fixing a water or gas plumbing problem, you don’t need to be home upgrading DIY megastar. Slight information can go a long way to dropping your expenses and overall trauma as well.

Water and Gas Plumbing Hacks Everyone Should Be Familiar With

So to help you keep more hard-earned-cash in your pocket, here, we are sharing a few exciting water and gas plumbing hacks that would save you a lot of stress.

By all means, these hacks may not be easy, and not everyone would be comfortable to do so. Not everyone will have tools and dedication to do, and at the same time, you will be doing all this DIY fix on your own risk since only Professional Plumber should carry out any plumbing and heating fix. You may be violating the law and putting you, your family and property in danger; if you are careful and even may end up damaging the equipment and your property.

CARRY OUT THE DIY FIX ONLY IF YOU ARE 100% SURE OTHERWISE HIRE A PROFESSIONAL PLUMBER.

Also before calling plumber, you need to know do you know just a plumber or Gas specialist. Read this article about the difference between a standard plumber and Gas Engineer.

Please Note: Gas Plumbing should be carried out by the licensed Gas Plumbers only. To begin with, drain your water heater to get rid of the water and mineral deposit. Fix a garden hosepipe to the tap at the bottom of the water heater and turn the tap to free the water. If possible, you should drain the water outside.

Try to find the hexagonal head of the anode rod at the crown of the water heater. You can make use of an air compressor and 1/2-inch drive impact wrench and 1-1/16-inch socket to release the shaft. After that, take away the rest using your hand. If it’s wedged in place, you can make use of WD-40 to lubricate it initially. And to replace the anode rod, make sure to stroke the Teflon pipe thread sealant on the threads at the bottom for an excellent seal.

Please note: Gas Plumbing is carried out by the professional Gas plumbers only. Insulation is one more trouble-free and straightforward way to decrease your water heater’s energy expenditure and save money on energy expenses. Make sure to check if your water heater is hot and look out for any cracks on insulation that might already be found on the water heater. You can furthermore set up heat traps on the warm as well as cold pipes that are linked to the water heater to decrease heat loss.

Addition of insulation to the first 5 or 6 feet of hot and cold water pipes that are attached to the water heater is a great idea and would trim down heat loss as well. Insulation will decrease heat loss and save you a lot of money on your heater’s power expenditure. The better the water heater is insulated, the more it would stay hot, saving you money.

You should clean your tanks at every six months to do away with all trash and dregs. Try turning the cold water supply off and attach a garden hosepipe to the water tap and drain the tank until the water starts running entirely clear. If the water remains mucky or grubby, you can get off the hosepipe for some time and let the trash stir up. Then go over the entire process once more. You will observe clear water running in a little while.

The most common reason for a tap leak or a faucet is the broken down washer present inside the stalk of the valve. However, the good news is that swapping the washer and replacing it with a new one is exceedingly easy. Just drape a cloth or a masking tape around the valve stalk to protect the lustre of the surface. After that, take off the valve stem using a suitable wrench. Take apart all the parts of the valve and replace the broken down washer with a new and strong one. Now, reassemble all the pieces of the tap and stiffen up the stem. You won’t find any faucet leaks from that day forward.

A lot of our day by day routine spins around the sink or hand basin. We frequently wash our face, wash our hands, brush our teeth, shave and put on face makeup as well. And for more than a few everyday jobs, we use water. So, whenever possible, you should fill up the sink and use that water rather than running the water all the time.

This might not appear like you’re saving anything, but that is because you don’t understand how much water is descending the drain while you wash your face and hands. As long as you fill it every time you call for using it and clean the hand basin on a regular basis, this is just as clean, sanitized as using running water. And you save a lot of water bills as well.

Again, it is a hack that would cost you cash, but the wealth it would save you is barely credible. Low-flow showerheads are showerheads that are intended to use a lesser amount of water considerably without dropping the water pressure you like. By and of it, your showers would still be just as pleasurable, possibly even more as these are likely to be waterfall-style showerheads. Though they are slightly expensive than typical models, they can save you around 30% on your water bill.

Have you ever detected plumbing pipes, dripping under your hand basin or sink on the connection? Well, if yes, then before you call an emergency plumber; try this cheap and simple hack. All you need for this is a plumber’s tape, a wrench, and a bucket.

So, here’s how to do it. First of all, turn off the water supply. If you aren’t familiar about where the local turn-off regulator is, you can use the main turn-off tap of your home to stop the water from the mains.

With a monkey wrench, you can slacken off the pipes and cut them off. Make sure you have a container below the connection since there will be water left in the tubes. Run the plumber’s tape in a clockwise direction around the threads followed by reconnecting the pipes. The tape will help you attain a tighter clasp without replacing the pipes.